Pelco Security Camera BBDF5L F User Manual

®
20131  
BBDF5-F, BBDF5L-F,  
and BBDF5S-F  
Back Boxes  
Installation/  
Operation Manual  
C1496M-A (2/02)  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150  
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should only be done by qualified service personnel and con-  
form to all local codes.  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P en-  
closure, it is designed for indoor use only and it must not be installed where exposed  
to rain and moisture.  
3. Only use replacement parts recommended by Pelco.  
4. After replacement/repair of this unit’s electrical components, conduct a resistance  
measurement between line and exposed parts to verify the exposed parts have not  
been connected to line circuitry.  
5. The installation method and materials should be capable of supporting four times the  
weight of the unit and equipment.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous volt-  
age constituting a risk of electric shock is  
present within this unit.  
C A U T I O N :  
RISK OF ELECTRIC SHOCK.  
This symbol indicates that there are impor-  
tant operating and maintenance instructions  
in the literature accompanying this unit.  
DO NOT OPEN.  
Please thoroughly familiarize yourself with the information in this manual prior to installa-  
tion and operation.  
DESCRIPTION  
The BBDF5-F, BBDF5L-F, and BBDF5S-F are plenum rated back boxes that can be in-  
stalled in hard ceiling or standard 2' x 2' (61 x 61 cm) suspended ceiling. The BBDF5-F  
and BBDF5L-F require 5.25 inches (13.34 cm) of space above the ceiling, and the  
BBDF5S-F needs only 2.75 inches (7 cm) of room.  
MODELS  
BBDF5-F  
BBDF5L-F  
BBDF5S-F  
Standard in-ceiling back box  
Extended in-ceiling box  
Shortened in-ceiling box  
INSTALLATION  
CONTENTS  
1
1
Back box with tilt table assembly installed (includes camera and lens if specified with order)  
Parts bag  
1
1
1
1
1
1
1
Conduit fitting with lock nut  
Safety chain bracket  
3-inch miniature coaxial cable assembly  
Compass tool  
Flat washer (models without camera)  
Split lock washer (models without camera)  
Screw (models without camera)  
Pelco Manual C1496M-A (2/02)  
3
 
HARD CEILING INSTALLATION  
1 PREPARE CEILING  
Locate the center point of the mounting location. Drill a hole in the ceiling using a 3/32-  
inch drill. Insert the compass tool into the hole. Use a pencil and the compass tool to  
draw a circle on the ceiling. Carefully cut out the circle.  
20116  
20120  
20124  
20122  
2 INSTALL THE BACK BOX  
Attach the conduit fitting, lock nut, and safety chain bracket. Install a safety chain/  
cable (not supplied) that will support up to 16 pounds (7.3 kg). Install one end of the  
safety chain/cable to the safety chain bracket and the other end to a support structure  
in the ceiling.  
Prepare the wiring for camera and lens power; refer to Tables A and B for wiring  
distances. Pull wiring into the back box through the conduit fitting.  
Compress the spring clips on the back box and push it through the hole until the clips  
spring back. Tighten the screws until you hear a clicking noise.  
ATTACH SAFETY CHAIN HERE  
CEILING  
20126  
20125  
CEILING  
20127  
4
Pelco Manual C1496M-A (2/02)  
 
SUSPENDED CEILING INSTALLATION  
1 PREPARE CEILING TILE  
NOTE: The ceiling tile  
cannot be thinner than  
0.50-inch (1.27 cm) or  
thicker than 1.75 inches  
(4.45 cm).  
Remove the ceiling tile from the ceiling. Insert the compass tool (supplied) into the  
center of the tile.  
(If necessary, use a 3/32-inch bit to drill a hole.) Draw a circle on the tile using the  
compass tool and a pencil. Carefully cut out the circle.  
20129  
20118  
20128  
2 INSTALL THE BACK BOX  
Attach the conduit fitting, lock nut, and safety chain bracket. Attach to the bracket one  
end of a safety chain/cable (not supplied) that will support up to 16 pounds (7.3 kg).  
Do not attach the other end yet.  
Compress the spring clips on the back box and push it through the hole until the clips  
spring back. Tighten the screws until you hear a clicking noise. Reinstall the ceiling tile.  
Remove an adjacent ceiling tile. Prepare the wiring for camera and lens power; refer to  
Tables A and B for wiring distances. Pull wiring into the back box through the conduit  
fitting. Attach the safety chain to a support structure. Replace the adjacent ceiling tile.  
CEILING  
CEILING  
20119  
20127  
ATTACH SAFETY CHAIN HERE  
20125  
Pelco Manual C1496M-A (2/02)  
5
 
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
* Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
Table B. 24 VAC Wiring Distances  
The following are the recommended maximum distances for 24 VAC  
with a 10-percent voltage drop. (Ten percent is generally the maximum  
allowable voltage drop for AC-powered devices.)  
Wire Gauge  
Total vA  
20  
18  
16  
14  
12  
10  
10 vA  
283 ft  
451 ft  
716 ft  
1142 ft 1811 ft 2880 ft  
(86)  
(137)  
(218)  
(348) (551) (877)  
CAMERA AND LENS INSTALLATION  
NOTE: If the camera and  
lens are already installed,  
refer to the camera and lens  
manuals for information on  
wiring and operating your  
equipment.  
To install the camera and lens:  
1
Install the miniature coaxial cable on the camera. Attach the camera and lens to the tilt  
table with the 1/4-20 screw and washers (supplied).  
20130  
2
3
To ensure that the lens will not hit the lower dome:  
• Place the lower dome over the back box with the camera and lens installed (do not  
attach dome).  
• If the lens touches the lower dome, adjust the tilt table assembly.  
Refer to the manual supplied with the camera and lens for the following information:  
• How to connect power and video wiring  
• How to make camera and lens adjustments  
6
Pelco Manual C1496M-A (2/02)  
 
SPECIFICATIONS  
MECHANICAL  
Construction  
Back Box:  
Mounting Bracket:  
Aluminum  
Steel  
Dimensions:  
GENERAL  
Environment:  
See dimension drawings  
Indoor and outdoor  
Operating Temperature: 32° to 120°F (0° to 49°C)  
Weight:  
BBDF5-F:  
BBDF5L-F  
BBDF5S-F:  
2.80 lb (1.27 kg)  
3.00 lb (1.36 kg)  
1.75 lb (.80 kg)  
(Design and product specifications subject to change without notice.)  
7.25 (18.13)  
6.60 (16.76)  
7.25 (18.13)  
6.60 (16.76)  
7.25 (18.13)  
6.60 (16.76)  
5.3  
7.6  
(19.33)  
(13.34)  
2.75  
(6.99)  
BBDF5L-F  
BBDF5S-F  
BBDF5-F  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES  
Pelco Manual C1496M-A (2/02)  
7
 
PRODUCT WARRANTY AND RETURN INFORMATION  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100  
WARRANTY  
or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide  
the following information:  
Pelco will repair or replace, without charge, any merchandise proved defective  
in material or workmanship for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on Pelco manufactured cameras (CC3500/CC3600 and MC3500/  
MC3600 Series); two years on all other cameras.  
Three years on Genex® Series (multiplexers, server, and keyboard).  
Two years on cameras and all standard motorized or fixed focal length lenses.  
Two years on Legacy®, CamclosureCamera Systems, CM6700/CM6800/  
CM8500/CM9500/CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome  
products.  
If there is a dispute regarding the warranty of a product which does not fall  
under the warranty conditions stated above, please include a written explana-  
tion with the product when returned.  
Two years on Spectra®, Esprit, and PS20 Scanners, including when used  
in continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which  
the item was received by Pelco.  
Two years on WW5700 series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders.  
One year (except video heads) on video cassette recorders (VCRs). Video  
heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous  
motion applications (that is, preset scan, tour and auto scan modes).  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call  
the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num-  
ber (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and  
refurbishing charge.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to Pelco, Clovis, California. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Goods returned for repair or credit should be clearly identified with the assigned  
CA or RA number and freight should be prepaid. Ship to the appropriate  
address below.  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelco’s  
liability for any claim, whether based on breach of contract, negligence, infringe-  
ment of any rights of any party or product liability, relating to the Products shall  
not exceed the price paid by the Dealer to Pelco for such Products. In no event  
will Pelco be liable for any special, incidental or consequential damages (includ-  
ing loss of use, loss of profit and claims of third parties) however caused, whether  
by the negligence of Pelco or otherwise.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:  
Intermediate Consignee  
American Overseas Air Freight  
320 Beach Road  
Burlingame, CA 94010  
USA  
Ultimate Consignee  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
USA  
The above warranty provides the Dealer with specific legal rights. The Dealer  
may also have additional rights, which are subject to variation from state to state.  
REVISION HISTORY  
Manual # Date  
Comments  
C1495M  
12/98  
2/02  
Original version.  
C1496M-A  
Added model BBDF5L-F and updated manual to new format.  
® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco.  
™ Esprit and Camclosure are trademarks of Pelco.  
© Copyright 2002, Pelco  
All rights reserved.  
8
Pelco Manual C1496M-A (2/02)  
 

Pelco Computer Hardware DX8100 ISCI User Manual
Philips Clock Radio AJ3551 User Manual
Philips Computer Monitor 107T40 User Manual
Philips DVR VR707 User Manual
Philips Portable CD Player AX2100 User Manual
Pioneer Automobile Accessories CNDV 700HD User Manual
Pioneer CD Player DEH P5250 User Manual
Planet Technology Telephone VIP 152T User Manual
Poulan Chainsaw 2002 06 User Manual
ProForm Home Gym PFCCSY29261 User Manual